From Fedora Project Wiki
< Architectures | ARM
m (Noted that Beta2 is out.) |
|||
| (One intermediate revision by one other user not shown) | |||
| Line 1: | Line 1: | ||
{{Admon/important|Beta 1 is Obsolete!|[[ARM/F13-ARM-Beta2|Beta 2]] is out.}} | {{Admon/important|Beta 1 is Obsolete!|[[Architectures/ARM/F13-ARM-Beta2|Beta 2]] is out.}} | ||
= Links = | = Links = | ||
| Line 49: | Line 49: | ||
* On PanadaBoards, no login prompt appears on the serial console. As a temporary workaround, uncomment the lines in <code>/etc/rc.d/rc.local</code> | * On PanadaBoards, no login prompt appears on the serial console. As a temporary workaround, uncomment the lines in <code>/etc/rc.d/rc.local</code> | ||
=== SMDKv310 Serial Login === | |||
* On Samsung SMDKv310, the tty port is ttySAC1. This device port is currently not created. A temporary (and very ugly) workaround would be to add the following lines to a rc script (like at the end of rc.sysinit): | |||
echo Creating Serial device /dev/ttySAC1 | |||
mknod /dev/ttySAC1 c 204 65 | |||
chmod 660 /dev/ttySAC1 | |||
chown root:dialout /dev/ttySAC1 | |||
Latest revision as of 06:21, 26 April 2011
Beta 1 is Obsolete!
Beta 2 is out.
Beta 2 is out.
Links
Beta 1 Release
- RootFS: http://scotland.proximity.on.ca/fedora-arm/beta/f13/rootfs-f13-beta-2011-02-22.tar.bz2
- Repository: http://arm.koji.fedoraproject.org/mash/beta/f13-arm-2011-02-21/f13-arm/arm/os/
Resources
- Fedora ARM Secondary Architecture project page
- ARM Koji Buildsystem
- #fedora-arm channel on the Freenode.net IRC network
- Fedora-ARM mailing list
Release Notes
Supported Architecture
- This release supports the ARM v5 architecture, little-endian, gnueabi, with thumb interworking (armv5tel). It will work on higher architecture versions but is not fully optimized for them. Popular supported devices include:
- SheevaPlug, GuruPlug, and other Marvell Kirkwood-based plug computers (including the OpenRD development systems) (armv5)
- BeagleBoard and PandaBoard systems (armv7)
- OLPC XO 1.75 (armv7)
- This release does not support armv4 and lower architecture versions. This means that it does not work on device including:
Kernel
- The Fedora ARM project does not currently provide a kernel. You will need to provide a kernel suitable for your device (either the one provided with the device, or one compiled for your device). Here are kernels suitable for some common ARM development devices:
Included Packages
- A comparision of the packages included in this beta release with the versions included in the primary 32-bit architecture (i686)
- Notable package sets not included or incomplete in the beta include OpenOffice.org, gstreamer, and KDE.
- Some languages (Ocaml, Haskell) do not yet suport ARM (in the versions used in F13). Therefore, any packages written in these languages are not yet available.
- Work is continuing on the remaining packages.
Using the Beta Release
- The beta release is a tarball of a minimal root filesystem. When coupled with a suitable kernel, it provides sufficient tools for login, network setup (wired or wireless), and software installation/removal via yum.
- Instructions for setting up Fedora ARM on a device
- The default root password is:
fedoraarm
Known Issues
PandaBoard Serial Login
- On PanadaBoards, no login prompt appears on the serial console. As a temporary workaround, uncomment the lines in
/etc/rc.d/rc.local
SMDKv310 Serial Login
- On Samsung SMDKv310, the tty port is ttySAC1. This device port is currently not created. A temporary (and very ugly) workaround would be to add the following lines to a rc script (like at the end of rc.sysinit):
echo Creating Serial device /dev/ttySAC1 mknod /dev/ttySAC1 c 204 65 chmod 660 /dev/ttySAC1 chown root:dialout /dev/ttySAC1