From Fedora Project Wiki
(Created page with "{{QA/Test_Case |description=This test case ensures that nmstate is working properly for managing network state on a Fedora system. |setup=Install the pre-release version of Fedora that is to be tested on a bare metal system using the default Anaconda settings. Make sure nmstate and its dependencies are installed on the system. |actions= * Open a terminal. * Execute the command nmstatectl show to display the current network state. * Create a new file called eth0.yml wit...") |
m (Update `nmstatectl apply eth0.yml` command) |
||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
{{QA/Test_Case | {{QA/Test_Case | ||
|description=This test case ensures that nmstate is working properly for managing network state on a Fedora system. | |description=This test case ensures that nmstate is working properly for managing network state on a Fedora system. | ||
|setup=Install the pre-release version of Fedora that is to be tested on a bare metal system using the default Anaconda settings. Make sure nmstate and its dependencies are installed on the system. | |setup=Install the pre-release version of Fedora that is to be tested on a bare metal system using the default Anaconda settings (unless it's Fedora CoreOS). Make sure nmstate and its dependencies are installed on the system. | ||
|actions= | |actions= | ||
| Line 29: | Line 29: | ||
</pre> | </pre> | ||
* Apply the new network configuration by executing the command nmstatectl apply | * Apply the new network configuration by executing the command nmstatectl apply eth0.yml. | ||
* Execute the command nmstatectl show again to verify that the changes have been applied. | * Execute the command nmstatectl show again to verify that the changes have been applied. | ||
* Reboot the system by executing the command sudo reboot. | * Reboot the system by executing the command sudo reboot. | ||
| Line 38: | Line 38: | ||
* The nmstatectl show command displays the current network state without errors. | * The nmstatectl show command displays the current network state without errors. | ||
* The eth0.yml file is created successfully. | * The eth0.yml file is created successfully. | ||
* The nmstatectl apply | * The nmstatectl apply eth0.yml command completes without errors. | ||
* The changes in the network configuration are reflected in the output of the nmstatectl show command. | * The changes in the network configuration are reflected in the output of the nmstatectl show command. | ||
* The system reboots successfully. | * The system reboots successfully. | ||
| Line 44: | Line 44: | ||
|optional=Optionally, test different network configurations, such as bonding, bridging, and VLANs, to ensure that nmstate can handle various scenarios. Also, try adding, modifying, and deleting network configurations to test the full range of nmstate capabilities. | |optional=Optionally, test different network configurations, such as bonding, bridging, and VLANs, to ensure that nmstate can handle various scenarios. Also, try adding, modifying, and deleting network configurations to test the full range of nmstate capabilities. | ||
}} | }} | ||
[[Category:CoreOS Test Cases]] | |||
Latest revision as of 08:59, 3 April 2024
Description
This test case ensures that nmstate is working properly for managing network state on a Fedora system.
Setup
Install the pre-release version of Fedora that is to be tested on a bare metal system using the default Anaconda settings (unless it's Fedora CoreOS). Make sure nmstate and its dependencies are installed on the system.
How to test
- Open a terminal.
- Execute the command nmstatectl show to display the current network state.
- Create a new file called eth0.yml with the following content:
interfaces:
- name: eth0
type: ethernet
state: up
ipv4:
enabled: true
address:
- ip: 192.168.1.2
prefix-length: 24
dhcp: false
ipv6:
enabled: true
address:
- ip: 2001:db8::2
prefix-length: 64
autoconf: false
dhcp: false
- Apply the new network configuration by executing the command nmstatectl apply eth0.yml.
- Execute the command nmstatectl show again to verify that the changes have been applied.
- Reboot the system by executing the command sudo reboot.
- After the system has rebooted, log in and open a terminal.
- Execute the command nmstatectl show to verify that the network configuration has persisted after the reboot.
Expected Results
- The nmstatectl show command displays the current network state without errors.
- The eth0.yml file is created successfully.
- The nmstatectl apply eth0.yml command completes without errors.
- The changes in the network configuration are reflected in the output of the nmstatectl show command.
- The system reboots successfully.
- The network configuration persists after the reboot, as shown in the output of the nmstatectl show command.
Optional
Optionally, test different network configurations, such as bonding, bridging, and VLANs, to ensure that nmstate can handle various scenarios. Also, try adding, modifying, and deleting network configurations to test the full range of nmstate capabilities.