Virt/SGX

SGX guidance

This page provides guidance on using SGX in the context of Fedora

Software installation

Until the packages are a standard part of Fedora, they are available from Copr. A minimal setup of a machine with SGX would involve the sgx-pckid-tool and sgx-mpa. The latter is recommended on multi-socket machines to enable automatic registration, and a functional no-op on single-socket machines, so it is easiest to simply always install it.

 $ dnf copr enable berrange/sgx-ng
 $ dnf install sgx-pckid-tool sgx-mpa

Firmware configuration

Machines will typically ship with SGX support disabled in the firmware, so while the software can be installed immediately, it won't be usable until SGX is enabled in the firmware. Determine whether SGX is enabled on the machine by looking for the existence of the /dev/sgx_enclave' device node. If missing, proceed with Enabling SGX, otherwise (optionally) proceed with Re-initializing SGX

Enabling SGX

Enabling SGX is a multi-step process requiring reboots. Cold boot the machine, and hit the magic key needed to enter the firmware menu, or use an integrated mgmt service such as iDrac if available.

Two settings must be toggled first, before other settings will become available:

1. Under the "System Security" menu (or similar) change the "Memory Encryption" option to "Multiple Keys"
2. Under the "Processor Settings" menu (or similar) change the "CPU Physical Address Limit" option to "Disabled"
3. Under the "Process Settings" menu (or similar) change the "SGX Factory Reset" option to "On"

With these changes made, select "Apply and reboot".

When the machine restarts, once again enter the firmware menus to toggled further settnigs

1. Under the "Process Settings" menu (or similar) change the "SGX" option to "On"
2. Under the "Process Settings" menu (or similar) change the " Enable/Disable SGX Auto MP Registration Agent " option to "Enabled"

With these changes made, select "Apply and reboot".

Note: if "SGX" option only offers "Off" as a choice this indicates that either the current hardware is not a compatible configuration, or another firmware setting is in an incompatible state. For example, SGX may require specific DIMM slot population. Consult your hardware vendor's documentation for further guidance.

Re-provisioning SGX

If a machine has previously been used with SGX enabled, a reset is recommended in the firmware for the new owner to take ownership of the platform. Cold boot the machine, and hit the magic key needed to enter the firmware menu, or use an integrated mgmt service such as iDrac if available.

1. Under the "Process Settings" menu (or similar) change the "SGX Factory Reset" option to "On"

With this change made, select "Apply and reboot".

When the machine restarts, once again enter the firmware menus to toggled further settnigs

1. Under the "Process Settings" menu (or similar) change the "Enable/Disable SGX Auto MP Registration Agent " option to "Enabled"

With this change made, select "Apply and reboot".

Validating setup

To validate a correct setup, the following checks should be made

• The devices nodes /dev/sgx_enclave, /dev/sgx_provision and /dev/sgx_vepc should exist, with the group set to sgx for the first & last, and sgxprv for the middle node.
• The mpa_manage -get_sgx_status command should report SGX status: MP_SGX_ENABLED, which means: SGX is enabled.
• The mpa_manage -get_registration_status command should report Registration process completed successfully.

Troubleshooting

• If the mpa_manage -get_registration_status command reports Registration is in progress., there are two likely problems

1. . The "Enable/Disable SGX Auto MP Registration Agent " UEFI option was not set to "Enabled"
2. . The mpa_registration.service systemd unit file was not started

If neither of those were the problem, then edit /etc/mpa_registration.conf to set the log level to info, and then re-start mpa_registration.service. The /var/log/mpa_registration.log file should now contain further details on what has happened.