Install and enable Samba
The following commands install Samba and set it to run via systemctl. This also sets the firewall to allow access to Samba from other computers.
sudo dnf install samba sudo systemctl enable smb --now firewall-cmd --get-active-zones sudo firewall-cmd --permanent --zone=FedoraWorkstation --add-service=samba sudo firewall-cmd --reload sudo systemctl enable smb --now
Sharing a directory under your home
In this example you will share a directory under your home and accessible only by your user.
Samba does not use the operating system users for authentication, so your user account must be duplicated in Samba. So if your account is "jane" on the host, the user "jane" must also be added to Samba. The usernames must be the same, however the passwords do not.
Create a user called "jane" in Samba:
sudo smbpasswd -a jane
Create a directory to be the share for Jane, and set the correct SELinux context:
mkdir /home/jane/share sudo semanage fcontext --add --type "samba_share_t" ~/share sudo restorecon -R ~/share
Samba configuration lives in the /etc/samba/smb.conf file. Adding the following section at the end of the file will instruct Samba to set up a share for Jane called "share" at the /home/jane/share directory just created.
[share]
comment = My Share
path = /home/jane/share
writeable = yes
browseable = yes
public = yes
create mask = 0644
directory mask = 0755
write list = user
Restart Samba for the changes to take effect:
sudo systemctl restart smb
Sharing a directory for many users
In this example, you will share a directory (outside your home directory) and create a group of users with the right to read/write to the share.
Remember that a Samba user must also be a system user, in order to respect filesystem permissions. This example creates a system group "myfamily" for two new users "jack" and "maria".
sudo groupadd myfamily sudo useradd -G myfamily jack sudo useradd -G myfamily maria
Tip: You can create these users without a system password in order to prevent access to the system via SSH or local login.
Adding jack and maria to Samba:
sudo smbpasswd -a jack sudo smbpasswd -a maria
Setting up the shared folder:
sudo mkdir /home/share sudo chgrp myfamily /home/share sudo chmod 770 /home/share sudo semanage fcontext --add --type "samba_share_t" /home/share sudo restorecon -R /home/share
Each share is described by its own section in the /etc/samba/smb.conf file. Add this section to the bottom of the file:
[family]
comment = Family Share
path = /home/share
writeable = yes
browseable = yes
public = yes
valid users = @myfamily
create mask = 0660
directory mask = 0770
force group = +myfamily
Explanation of the above:
- valid users: only users of the group family have access rights. The @ denotes a group name.
- force group = +myfamily: files and directories are created with this group, instead of the user group.
- create mask = 0660: files in the share are created with permissions to allow all group users to read and write files created by other users.
- directory mask = 0770: as before, but for directories.
Restart Samba for the changes to take effect:
sudo systemctl restart smb
Change a samba user password
Remember: system and samba password can be different. The system user is mandatory in order to handle filesystem permissions.
sudo smbpasswd maria
Remove a samba user
sudo smbpasswd -x maria
If you don't need the system user, remove it as well:
sudo userdel -r maria
Troubleshooting and logs
Samba log files are located in /var/log/samba/
tail -f /var/log/samba/log.smbd
You can increase the verbosity adding this directive to /etc/samba/smb.conf in the [global] stanza:
[global]
loglevel = 5
To validate configuration file syntax: testparm
To display current samba connections, use the smbstatus command.
- Be sure that the user exists as system user as well as samba user - Check if the shared directory has the right SELinux context
$ ls -dZ /home/share unconfined_u:object_r:samba_share_t:s0 /home/share
- Check if the system user has access rights to the shared directory ls -ld /home/share drwxrwx---. 5 root myfamily 4096 9 gen 15.45 /home/share
In this case the user should be in the myfamily group
- check in the configuration file if the user has access rights granted or he is in the appropriated group
- Check in the samba configuration file if the user/group has write permissions - Check user group membership - Check the share directory permissions