Trouble running script
Wed Nov 5 17:29:00 UTC 2008
I recently purchase a Sandisk SD card to try to do the Fedora 10 installation on my XO. I could not follow the installation instructions as I have an older SD card reader that will not recognize the 4Gb SDHC card.
So, I tried to do a self installation procedure on the XO. I copied the F10 live image to a USB stick, and inserted it and the SD card in thee XO. I downloaded the live iso script and attempted to run it. This failed with lots of 'no such file or directory' errors. The 'already set up' error is because this log was a second attempt, so that I could capture the log. Log follows:
bash-3.2# bash livecd-iso-to-disk.sh --xo --overlay-size-mb 320 --swap-size-mb 256 /media/PNY4/Fedora-10-Snap3-i686-Live/F10-Snap3-i686-Live.iso /dev/mmcblk0p1 Verifying image... livecd-iso-to-disk.sh: line 304: checkisomd5: command not found Are you SURE you want to continue? Press Enter to continue or ctrl-c to abort y Already set up as live image. Deleting old OS in fifteen seconds... Copying live image to USB stick mount: unknown filesystem type 'squashfs' cp: cannot stat `/media/cdtmp.1T1vVo/LiveOS/ext3fs.img': No such file or directory Cleaning up to exit... umount: /media/cdtmp.1T1vVo: not mounted umount: /media/cdtmp.1T1vVo: not mounted cp: cannot stat `/media/cdtmp.1T1vVo/isolinux/*': No such file or directory Updating boot config file sed: can't read /media/usbdev.CifSx0/syslinux/isolinux.cfg: No such file or directory Initializing persistent overlay file dd: opening `/media/usbdev.CifSx0/LiveOS/overlay-SAN4fedora-4911-BF89': No such file or directory sed: can't read /media/usbdev.CifSx0/syslinux/isolinux.cfg: No such file or directory sed: can't read /media/usbdev.CifSx0/syslinux/isolinux.cfg: No such file or directory Initializing swap file dd: opening `/media/usbdev.CifSx0/LiveOS/swap.img': No such file or directory /media/usbdev.CifSx0/LiveOS/swap.img: No such file or directory Setting up /boot/olpc.fth file egrep: /media/usbdev.CifSx0/syslinux/isolinux.cfg: No such file or directory Installing boot loader mv: cannot stat `/media/usbdev.CifSx0/syslinux/isolinux.cfg': No such file or directory umount: /media/cdtmp.1T1vVo: not mounted umount: /media/usbdev.CifSx0: not mounted USB stick set up as live image!
Any work arounds, or do I have to go out and get a SDHC reader? Rmyers7 17:29, 5 November 2008 (UTC) rmyers7 at mindspring dot com
a little follow-up
The following is now on the SD card:
- the volume name I set with mkfs.msdos
- /.olpc.store directory and contents (not relevant to this, but shows card is ok)
- empty /LiveOS directory
- /syslinux directory with ldlinux.sys in it
Should the live image simply be copied to /LiveOS? I've never done this before, so I don't know what correct looks like. Rmyers7
Wed Nov 5 18:30:08 UTC 2008
User:jlaska - To address the No such file messages it appears you'll need to install some missing packages. Try:
# yum install isomd5sum squashfs-tools
Also, what type of system are you running the script on (Fedora8, Fedora9, Fedora10)?
Thanks for the response. I'll try that. I saw the isomd5sum error, but as it seemed to me just to be just a warning for the checksum, I ignored it. I'm trying this on an XO with build 767, which is Fedora 9. My other linux box is Fedora 8. I'm going to try to do the installation on a 2Gb SD card on the Fedora 8 box. If that succeeds at least I'll know what success looks like. I didn't try this before as the 2Gb card I have handy is formatted ext2. But I looked at the script and see that it works with ext[23] as well as fat. Rmyers7
I did the installs and behavior changed, but I still get errors. I'm now trying to more fully understand the installation script to figure out where the issue is. However, I'm trying another tack - with its own issues. See my other section 'Am I missing something?' Rmyers7
Am I missing something?
I'm trying to get this going. My current tack is not quite following the script, so I don't know if that is the issue. However, I get to a point where there seems to be some information missing here.
What I did/where I'm at
I don't have a SDHC reader, and haven't run out to get one yet. I'm trying to do the install on a 2Gb slow SD card, just as a proof of concept. The card is formatted ext2, and has about 200Mb on it that I chose not to scrag - as the info here implies that the card need not be dedicated.
I ran the livecd script and the final results were a filled SD card with a 1.7G image at /LiveOS/ext3fs.img. Is this correct - does the image fill all available space, or did I run out on a 2G card?
The XO has a developer key and security is disabled.
Something missing
So now I have a card with an image (good???). If I insert it and on powering up, the XO simply powers up normally. If I interrupt the boot, there doesn't seem to be anything to point to for an alternate boot. 'boot sd:\LiveOS\ext3fs.img' doesn't work. There are no instructions here as to how to actually start the F10 image. How does one get into it? Rmyers7 00:14, 6 November 2008 (UTC)
self answered
Image is not good because we ran out of space.
The unsquashed image is 3Gb, so it looks like about 3.6Gb is needed to install. However the livecd script doesn't report a problem because the squashed size is 700Mb, givving a bougs guess of 1.3GB needed.
And because the image never completed, the forth boot file never gets copied.